# T-post pounder: which gas driver and sleeve to use | RediDriver

> A gas powered T-post pounder from RediDriver: the REDIclassic52 drives T-posts with no sleeve, the REDIboss78 with the 1 3/4" reducer sleeve.

Source: https://redidriver.com/answers/t-post-pounder/

---

The short answer

### Which RediDriver for T-posts

The [REDIclassic52](https://redidriver.com/product/rediclassic52-with-2-id-guide-tube/) drives T-posts with **no reducer sleeve** : they run straight down its 2" guide tube, and at 32 lbs it is the lightest machine in the line. The [REDIboss78](https://redidriver.com/product/rediboss78-post-driver-with-3-1-8-id-guide-tube/) drives them with the [1 3/4" reducer sleeve](https://redidriver.com/product/1-3-4-reducer-sleeve-for-rediboss78/), which keeps the T-post centred in its 3 1/8" tube, and it also handles round posts up to 3" OD. Both run a Honda GX35.

| Driver | T-posts | Weight | Joules | Impact rate | Also drives |
| --- | --- | --- | --- | --- | --- |
| [REDIclassic52](https://redidriver.com/product/rediclassic52-with-2-id-guide-tube/) | No sleeve needed | 32 lbs | 26 | 1720 BPM | Wood, steel and round posts under 2"; rods and rebar with the rod sleeve |
| [REDIboss78](https://redidriver.com/product/rediboss78-post-driver-with-3-1-8-id-guide-tube/) | With the 1 3/4" reducer sleeve | 35 lbs | 26 | 1740 BPM | Round posts up to 3" OD, U-channel and Carsonite types with their adapters |

← swipe the table

Want the hardest hit in the line? The MEGAmulti delivers 30 joules at 1780 BPM, and the REDIboss78’s 1 3/4" reducer sleeve fits it too. Driving T-posts in rock or caliche? Read [T-posts in rocky ground](https://redidriver.com/answers/driving-t-posts-in-rocky-ground/).

Running it

### Fuel, care and reach

- Straight unleaded gas, no mixing, and 10W-30 engine oil.
- EP 0 low viscosity grease for the hammer and crank. Use only EP 0, do not substitute.
- Recoil start. Inclinable, so the engine runs at any angle. Handles are spring isolated.
- Over 100 dB, hearing protection required.
- Clean it after each use. A full service once a year, especially with frequent use.
- The handle extension kit adds 4 feet of overall length, enough to drive 8 to 10 foot posts from the ground.

The full care sheet is on [How to use](https://redidriver.com/how-to-use-redidriver/).

From the field

### What owners report

> The Texas Hill Country is gorgeous, but the ground is really rocky. I researched for months and found the golden tool: the RediDriver. It drives through caliche and hard ground and makes driving T-posts amazingly easier. Now my guys fight over being the post-driver man of the day.

> This thing performed like nothing I have ever used! After using it, I'll never part with it! Honestly, it was taking longer to climb down, move the ladder, and back up than it took to drive the post 4'6" deep. I'll never use a hand driver ever again!

> We drove 177 posts from 10:30 to 1:30 with a half hour lunch, a minute a piece with laying them out. This driver is like the Little Engine That Could. We had time to build 1000 feet, then stretch another 1300 to prep for the next day.

In their own words, from [The Field](https://redidriver.com/your-redidriver/).

Own a RediDriver? Tell other crews how it did on your ground: the posts, the soil, how many you drove.

[Review us on Google](https://search.google.com/local/writereview?placeid=ChIJ_ZfZiysryYARzu1TGqnMWuU)

Questions

### Asked and answered

On the REDIclassic52, no: T-posts run straight down its 2" guide tube. On the REDIboss78, yes: the 1 3/4" reducer sleeve keeps the T-post centred in the 3 1/8" guide tube.

The REDIclassic52, at 32 lbs. It hits with 26 joules at 1720 BPM from a Honda GX35.

Yes, with the handle extension kit. It adds 4 feet of overall length, enough to drive 8 to 10 foot posts from the ground without a ladder.

[Compare the drivers](https://redidriver.com/specs/) [Check what fits](https://redidriver.com/compatibility/)

More answers
[Gas vs pneumatic vs hydraulic post drivers](https://redidriver.com/answers/gas-vs-pneumatic-vs-hydraulic-post-drivers/) [Driving T-posts in rocky ground](https://redidriver.com/answers/driving-t-posts-in-rocky-ground/) [Gas powered post pounder: which one fits your posts](https://redidriver.com/answers/gas-powered-post-pounder/) [Vineyard post driver: which model fits your posts](https://redidriver.com/answers/vineyard-post-driver/)
